Starting Initialization of FMAN0 Loading ucode for FMAN0, size: 6992, ver: 101.08.00 Starting Initialization of FMAN1 Loading ucode for FMAN1, size: 6992, ver: 101.08.00 Serdes Protocol: 0x10 CPU Reset Reason = 0x0001 Initializing GIGE SW... PPC P40X0 (partnum 0x8023), Revision 03.00, (Core Version 03.01) Sys Clock: 100 Mhz Core Clock: 1500 Mhz Plat Clock: 800 Mhz LBC Clock: 25 Mhz MEM Clock: 1300 Mhz System Bootstrap, Version 3.4(20160331:102636) [ASR9K ROMMON], Copyright (c) 1994-2016 by Cisco Systems, Inc. Compiled Thu 31-Mar-16 15:56 by skumarss Board Type: 0x100401 CPU Board => Rev: 0x3 ========= FPGA ver: 01.0f CBC: 16.72 DTI programmed with latest image
TIMEX programmed with latest image MLAN init done: ready to connect to the network BCM5482PhyInit () : Port 0 --> SFP Not present BCM5482PhyInit () : Port 1 --> SFP Not present set_chassis_type: chassis_type=0xef0400 found=TRUE ASR9001E (P40X0 PPC) RSP platform with 8192 Mb of main memory program load complete, entry point: 0x100000, size: 0x2ac20 Set baud rate to: 9600 program load complete, entry point: 0x100000, size: 0x2ac20 Set baud rate to: 9600 MBI Candidate = disk0:asr9k-os-mbi-6.1.4/0x100000/mbiasr9k-rp.vm CARD_SLOT_NUMBER: 0 CPU_INSTANCE: 1 MBI Validation starts ... Disabling both Mgt LAN ports Enabling Cluster Port 0 and disabling Port 1 BCM5482 cluster port-1 reset done !! Port 0. SFP Not Ready (0:0). Init failed dtsec_init_hw: configuring DTSEC (port 8) for: 1GB, Full Duplex Interface link changed state to UP. Interface link state up. MBI validation sending request. HIT CTRL-C to abort .......... No MBI confirmation received from dSC CARD_SLOT_NUMBER: 0 CPU_INSTANCE: 1 MBI Validation starts ... Enabling Cluster Port 1 and disabling Port 0 BCM5482 cluster port-0 reset done !! Port 1. SFP Not Ready (0:0). Init failed
dtsec_init_hw: configuring DTSEC (port 8) for: 1GB, Full Duplex Interface link changed state to UP. Interface link state up. MBI validation sending request. HIT CTRL-C to abort .......... No MBI confirmation received from dSC AUTOBOOT: Boot string = disk0:asr9k-os-mbi-6.1.4/0x100000/mbiasr9k-rp.vm,1; AUTOBOOT: autobootstate=0, autobootcount=0, cmd=boot disk0:asr9k-os-mbi-6.1.4/0x100000/mbiasr9k-rp.vm Boot Status 16 program load complete, entry point: 0x100000, size: 0x2ac20 Set baud rate to: 9600 MBI size from header = 21979816,Bootflash resident MBI filesize = 21979816 .................................................................................... program load complete, entry point: 0x204184, size: 0x14f53a8 Boot Status 17 Config = SMP, Running = SMP Board type: 0x00100401 Card Capability = 0x00000000 ############################################# BSP: Board type : ASR9K-RSP-I tracelogger: starting tracing in background ring mode tracelogger running with args: -startring -F 1 -F 2 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS XR Software for the Cisco XR ASR9K, Version 6.1.4 Copyright (c) 2017 by Cisco Systems, Inc. Jan 31 23:44:18.956: Install Setup: Booting with committed software Initializing Punt-switch ... Initializing Punt-switch ... Set RP CPU Cluster port in DSA mode Init STP group for Cluster ports forwarding state control done Cluster: Boot Request Filter configured Cluster: Control Link monitor proto filter configured Successfully initialized punt-switch(26 ports). SPP has connected to PAKMAN.... SPP registered CPU port 4 with DPAA SPP Port Idx 0 MAC addr --> 00:70:72:00:00:08 RP/0/RSP0/CPU0:Jan 31 23:43:48.748 : imio[64]: %PLATFORM-IMIO-3-OPERATION_NOTIFY : imio_main: cold start ios con0/RSP0/CPU0 is now available
Press RETURN to get started. |